Glossary entry (derived from question below)
English term or phrase:
Bauart spring
Polish translation:
sprężyna samozamykania drzwi
Added to glossary by
Anna Gredecka (X)
Aug 28, 2019 17:00
5 yrs ago
2 viewers *
English term
Bauart spring
English to Polish
Tech/Engineering
Mechanics / Mech Engineering
Proposed translations
(Polish)
4 +1 | sprężyna samozamykania drzwi | Crannmer |
2 | sprężyna dociskowa | geopiet |
Proposed translations
+1
2 hrs
Selected
sprężyna samozamykania drzwi
Po zamontowaniu jej kominek jest zgodny z Bauart 1.
4 KudoZ points awarded for this answer.
1 hr
sprężyna dociskowa
.
Reference comments
1 hr
Reference:
Exchange of the handle bar on the Aduro 7
The package contains:
1 handle bar
1 cylinder
1 claw
1 lathe screw
1 distance disc
2 bushes
1 split pin
Directions:
Please wear a pair of working gloves, when exchanging the handle bar.
5. Removal off the door
a. Remove the spring by using a pair of tongs or a screwdriver. The spring must be removed from the door, not the stove. Carefully pull out the spring
b. Remove the upper hinge – please hold the door whilst unscrewing the screws. When the upper hinge is off, you can lift off the door from the lower hinge
Place the door with the front down on a soft material in order to protect the enamel paint
6. Dismantling of the handle bar
a. Loosen the upper bolt on the handle bar
b. Loosen the lathe screw on the upper claw with an allen key
c. Take out the handle bar, the old claw and the distance discs
d. Unscrew the handle from the handle bar, since you need to mount this again on the new handle bar
7. Mounting of the new handle bar
a. Fasten the „old“ handle to the new handle bar The new handle bar and the claw must be assembled before the further assembling
b. Place a distance disc on the handle bar and lead the handle bar through the hole at the bottom of the door
c. Then place a bush and the cylinder. Press the bush hard into the hole. The bush must sit as tight as possible
d. Place the lathe screw in the claw without tightening the lathe screw
e. Pull the handle bar through the other 2 holes and finally place the last bush and the claw at the end of the handle bar.
f. Place the split pin on the cylinder. The bush has to sit correct in the hole in the door, in order to be able to mount the split pin correct. This may be done by using a small hammer
g. Tighten the lathe screw
8. Remounting of the door on the stove
a. Place the door on the hinges
b. Mount the hinges on the stove again
c. Remount the spring with a pair of tongs Turn the Bauart spring a half round in order to place it in the hole at the top of the door (requires a little patience)
d. Now the door ought to close correct again
Hereafter you can use the stove again.
http://aduroshop.dk/upload_dir/shop/samlevejledninger/51096....
The package contains:
1 handle bar
1 cylinder
1 claw
1 lathe screw
1 distance disc
2 bushes
1 split pin
Directions:
Please wear a pair of working gloves, when exchanging the handle bar.
5. Removal off the door
a. Remove the spring by using a pair of tongs or a screwdriver. The spring must be removed from the door, not the stove. Carefully pull out the spring
b. Remove the upper hinge – please hold the door whilst unscrewing the screws. When the upper hinge is off, you can lift off the door from the lower hinge
Place the door with the front down on a soft material in order to protect the enamel paint
6. Dismantling of the handle bar
a. Loosen the upper bolt on the handle bar
b. Loosen the lathe screw on the upper claw with an allen key
c. Take out the handle bar, the old claw and the distance discs
d. Unscrew the handle from the handle bar, since you need to mount this again on the new handle bar
7. Mounting of the new handle bar
a. Fasten the „old“ handle to the new handle bar The new handle bar and the claw must be assembled before the further assembling
b. Place a distance disc on the handle bar and lead the handle bar through the hole at the bottom of the door
c. Then place a bush and the cylinder. Press the bush hard into the hole. The bush must sit as tight as possible
d. Place the lathe screw in the claw without tightening the lathe screw
e. Pull the handle bar through the other 2 holes and finally place the last bush and the claw at the end of the handle bar.
f. Place the split pin on the cylinder. The bush has to sit correct in the hole in the door, in order to be able to mount the split pin correct. This may be done by using a small hammer
g. Tighten the lathe screw
8. Remounting of the door on the stove
a. Place the door on the hinges
b. Mount the hinges on the stove again
c. Remount the spring with a pair of tongs Turn the Bauart spring a half round in order to place it in the hole at the top of the door (requires a little patience)
d. Now the door ought to close correct again
Hereafter you can use the stove again.
http://aduroshop.dk/upload_dir/shop/samlevejledninger/51096....
Discussion
https://pl.bab.la/slownik/niemiecki-polski/bauart
cccccccccccccccc
1. Drzwi paleniska
2. Króciec rury dymowej
3. Pojemnik na drzewo
4. Regulator powietrza pierwotnego
5. Uchwyt drzwi
6. Ściany
7. Ruszt
8. Popielnik
9. Tabliczka znamionowa (na tylnej ścianie)
10. Sprężyna samozamykacza drzwi
http://wamsler.pl/pdfy/primo_u.pdf
ccccccccccc
Porównaj z
element 51068
http://www.aduroshop.com/upload_dir/shop/kategoribilleder/H1...