This question was closed without grading. Reason: Answer found elsewhere
May 29, 2016 23:11
8 yrs ago
1 viewer *
English term
Main # I
English to German
Tech/Engineering
Engineering (general)
CNC, grinding machines, o
Es geht um Schleifmaschinen und brauche bitte Eure Hilfe bei dem Begriff "Main # I". Vielen Dank
Clamping “V” Pre-support with clamp flanges in **Main # I** and # V.
Axial positioner:
Clamping “V” Pre-support with clamp flanges in **Main # I** and # V.
Axial positioner:
Reference comments
1 hr
Reference:
External clamping system / Controlled flanges / Main I/O PCB M-Code Relays
The TDF-2 NC is fixed to the flange using an external clamping system, and the basic version has a large facing head, a main drive, a clamping device and the Zaxis for vertical movements.
http://efco-dueren.de/english/turning/cnc-controlled-flange-...
Main I/O PCB M-Code Relays
M21-M28 Optional User M Function with M-Fin
The M codes M21 through M28 are optional for user-defined relays. Each M code activates one of the optional relays. The Reset button will stop any operation that is waiting for a relay-activated accessory to finish. Also see M51-58 and M61-68.
Some or all of the M21-25 (M21-M22 on Toolroom, Office and Mini mills) on the I/O PCB may be used for factory-installed options. Inspect the relays for existing wires to determine which have been used.
Only one relay is activated at a time. A typical operation is to command a rotary product. The sequence is: Run the machining portion of a CNC part program.
Stop CNC motion and command rotary motion through the relay. Wait for a finish (stop) signal from the rotary product. Continue the CNC part program.
M-Code Relays
These outputs can be used to activate probes, auxiliary pumps or clamping devices
etc. The auxiliary devices are electrically connected to the terminal strip for the individual relay. The terminal strip has a position for, Normally Open (NO), Normally Closed (NC) and Common (COM).Ű
Optional M-Code Relay Board (Mounted above Main I/O PCB)
--------------------------------------------------
Note added at 1 hr (2016-05-30 00:42:15 GMT)
--------------------------------------------------
http://www.cnccookbook.com/CCCNCMillingWorkholding.html
http://efco-dueren.de/english/turning/cnc-controlled-flange-...
Main I/O PCB M-Code Relays
M21-M28 Optional User M Function with M-Fin
The M codes M21 through M28 are optional for user-defined relays. Each M code activates one of the optional relays. The Reset button will stop any operation that is waiting for a relay-activated accessory to finish. Also see M51-58 and M61-68.
Some or all of the M21-25 (M21-M22 on Toolroom, Office and Mini mills) on the I/O PCB may be used for factory-installed options. Inspect the relays for existing wires to determine which have been used.
Only one relay is activated at a time. A typical operation is to command a rotary product. The sequence is: Run the machining portion of a CNC part program.
Stop CNC motion and command rotary motion through the relay. Wait for a finish (stop) signal from the rotary product. Continue the CNC part program.
M-Code Relays
These outputs can be used to activate probes, auxiliary pumps or clamping devices
etc. The auxiliary devices are electrically connected to the terminal strip for the individual relay. The terminal strip has a position for, Normally Open (NO), Normally Closed (NC) and Common (COM).Ű
Optional M-Code Relay Board (Mounted above Main I/O PCB)
--------------------------------------------------
Note added at 1 hr (2016-05-30 00:42:15 GMT)
--------------------------------------------------
http://www.cnccookbook.com/CCCNCMillingWorkholding.html
Note from asker:
Thank you Erzsebet |
Discussion
Main sollte ja mittlerweile klar sein ...