Oct 2, 2019 16:14
5 yrs ago
English term
SB position
English to Russian
Tech/Engineering
Mechanics / Mech Engineering
Electrical manual for a lathe
Здравствуйте!
Перевожу руководство по эксплуатации токарного станка. В разделе Power Up Step попалось такое предложение:
The key is turned to the normally open button SB position and pull the door switch SQ mandrel, so that in the state of repair.
Прошу помочь разобраться с аббревиатурами SB и SQ. На всякий случай привожу предыдущие два пункта из раздела:
4.1 Cut off external power supply, open electrical boxes, cut off all electrical breaker box
4.2 Red mushroom head on the steering box by pressing the emergency stop button on the operation panel attached
...поскольку составлено руководство носителями китайского, грамматики в нём нет совсем. О сути текста можно догадываться только по значениям отдельных слов.
Буду благодарна за помощь!
Перевожу руководство по эксплуатации токарного станка. В разделе Power Up Step попалось такое предложение:
The key is turned to the normally open button SB position and pull the door switch SQ mandrel, so that in the state of repair.
Прошу помочь разобраться с аббревиатурами SB и SQ. На всякий случай привожу предыдущие два пункта из раздела:
4.1 Cut off external power supply, open electrical boxes, cut off all electrical breaker box
4.2 Red mushroom head on the steering box by pressing the emergency stop button on the operation panel attached
...поскольку составлено руководство носителями китайского, грамматики в нём нет совсем. О сути текста можно догадываться только по значениям отдельных слов.
Буду благодарна за помощь!
Proposed translations
(Russian)
3 +1 | положение кнопочного переключателя | Enote |
2 | SB - South Bend lathe / Push button switch (jogging switch) type SB **** | Erzsébet Czopyk |
Proposed translations
+1
14 mins
Selected
положение кнопочного переключателя
sb - это так китайцы Button Switch сократили, наверняка
Кстати, если есть такое же обозначение на схеме, то SB в тексте не переводится (можно добавить расшифровку), чтобы не смущать рассматривающего схему человека
Кстати, если есть такое же обозначение на схеме, то SB в тексте не переводится (можно добавить расшифровку), чтобы не смущать рассматривающего схему человека
4 KudoZ points awarded for this answer.
Comment: "Спасибо!
Да, похоже, SB и SQ - это обозначения деталей на схеме. Просто схема в руководстве не приводится)"
1 hr
SB - South Bend lathe / Push button switch (jogging switch) type SB ****
About 1,220,000 results (0.64 seconds)
Search Results
Web results
[PDF] SouthBend Lathe Manual - UFL MAE
www2.mae.ufl.edu › designlab › Manuals › SouthBend Lathe Manual
16" South Bend Precision Toolroom Lathe (Circa 1958) ..... the machine to open or remove doors/covers as required by ..... OFF position, reset the stop button by.
[PDF] PRECISION CENTER LATHE
https://www.wttool.com › common › manuals
Jan 6, 2014 - Position lathe on foundation and adjust each of ..... Release the clamping lever and .... A : Push button switch(jogging switch)type SB 3051A.
Please help me understand the fascination with SB lathes. [Archive ...
bbs.homeshopmachinist.net › ... › General
Jul 26, 2006 - 101 posts - 49 authors
I was 15 years old and it was a South Bend lathe that I learned on. ... light duty tailstock with no camlock, noisy open chip grabbing QC ...... but I hit the wrong button. ..... my father-in-law being offered a head mechanic position to build motors for formula 1, or a good friend of mine that ports heads for nascar)
1923 SB Lathe Help. Binding - Practical Machinist
https://www.practicalmachinist.com › south-bend-lathes › 1923-sb-lathe-he...
Apr 18, 2018 - It is not like the levers that I have seen on other SB lathes. This one is a knob that you turn to loosen and then select the up or down position.
South Bend 6-12 Magnaturn CNC Lathe
--------------------------------------------------
Note added at 1 hr (2019-10-02 17:52:32 GMT)
--------------------------------------------------
SB from the South Bend Lathe Co.
South Bend Lathe, Inc.
C/O Technical Documentation Manager
P.O. Box 2027
Bellingham, WA 98227
Email: [email protected]
https://d27ewrs9ow50op.cloudfront.net/manuals/sb1054f_m.pdf
raise the CF level to 4
--------------------------------------------------
Note added at 1 hr (2019-10-02 17:54:15 GMT)
--------------------------------------------------
Токарный станок South Bend "10 (Heavy) Lathe ...
https://www.chipmaker.ru › ... › Токарные станки - Translate this page
Jan 26, 2013 - Токарный станок South Bend "10 (Heavy) Lathe. ... gentoo_m Отправлено 16 November 2014 - 21:54 .... К концу 1930-х годов фирма South Bend выпускала две модели 9-и дюймового токарного станка: более лёгкую ... качестве дани “инструментальности” – прецизионным ходовым винтом (без ...
SOUTH BEND 9" комплектация и восстановление ...
https://www.chipmaker.ru › ... › Токарные станки
Translate this page
Автор: alexeyhim - Лёший СП, 9 ноября 2014 в Токарные станки ... сего чуда http://www.lathes.co...inch/index.html Очень похож на станок с первого фото, но шкивы .... 199-A, UMD 11/16 Collet lathe, This lathe has the smaller, 1 7/8 by 8 TPI spindle thread ..... запчасти и оснастку для токарного станка South bend 9".
--------------------------------------------------
Note added at 1 hr (2019-10-02 17:56:31 GMT)
--------------------------------------------------
SQ mandrel: SQUARE CORNERS
Search Results
Web results
[PDF] SouthBend Lathe Manual - UFL MAE
www2.mae.ufl.edu › designlab › Manuals › SouthBend Lathe Manual
16" South Bend Precision Toolroom Lathe (Circa 1958) ..... the machine to open or remove doors/covers as required by ..... OFF position, reset the stop button by.
[PDF] PRECISION CENTER LATHE
https://www.wttool.com › common › manuals
Jan 6, 2014 - Position lathe on foundation and adjust each of ..... Release the clamping lever and .... A : Push button switch(jogging switch)type SB 3051A.
Please help me understand the fascination with SB lathes. [Archive ...
bbs.homeshopmachinist.net › ... › General
Jul 26, 2006 - 101 posts - 49 authors
I was 15 years old and it was a South Bend lathe that I learned on. ... light duty tailstock with no camlock, noisy open chip grabbing QC ...... but I hit the wrong button. ..... my father-in-law being offered a head mechanic position to build motors for formula 1, or a good friend of mine that ports heads for nascar)
1923 SB Lathe Help. Binding - Practical Machinist
https://www.practicalmachinist.com › south-bend-lathes › 1923-sb-lathe-he...
Apr 18, 2018 - It is not like the levers that I have seen on other SB lathes. This one is a knob that you turn to loosen and then select the up or down position.
South Bend 6-12 Magnaturn CNC Lathe
--------------------------------------------------
Note added at 1 hr (2019-10-02 17:52:32 GMT)
--------------------------------------------------
SB from the South Bend Lathe Co.
South Bend Lathe, Inc.
C/O Technical Documentation Manager
P.O. Box 2027
Bellingham, WA 98227
Email: [email protected]
https://d27ewrs9ow50op.cloudfront.net/manuals/sb1054f_m.pdf
raise the CF level to 4
--------------------------------------------------
Note added at 1 hr (2019-10-02 17:54:15 GMT)
--------------------------------------------------
Токарный станок South Bend "10 (Heavy) Lathe ...
https://www.chipmaker.ru › ... › Токарные станки - Translate this page
Jan 26, 2013 - Токарный станок South Bend "10 (Heavy) Lathe. ... gentoo_m Отправлено 16 November 2014 - 21:54 .... К концу 1930-х годов фирма South Bend выпускала две модели 9-и дюймового токарного станка: более лёгкую ... качестве дани “инструментальности” – прецизионным ходовым винтом (без ...
SOUTH BEND 9" комплектация и восстановление ...
https://www.chipmaker.ru › ... › Токарные станки
Translate this page
Автор: alexeyhim - Лёший СП, 9 ноября 2014 в Токарные станки ... сего чуда http://www.lathes.co...inch/index.html Очень похож на станок с первого фото, но шкивы .... 199-A, UMD 11/16 Collet lathe, This lathe has the smaller, 1 7/8 by 8 TPI spindle thread ..... запчасти и оснастку для токарного станка South bend 9".
--------------------------------------------------
Note added at 1 hr (2019-10-02 17:56:31 GMT)
--------------------------------------------------
SQ mandrel: SQUARE CORNERS
Something went wrong...